ttb-zwave3
Version:
ZWave support for the Thingbox (http://TheThingbox.io) and TimeSquAir (http://TimeSquAir.io)
138 lines (118 loc) • 6.84 kB
JavaScript
;
// productIDTotal refers to '../../node_modules/openzwave-shared/deps/open-zwave/config/manufacturer_specific.xml'
/*
bool Manager::SetConfigParam (
uint32 const _homeId,
uint8 const _nodeId,
uint8 const _param,
int32 _value,
uint8 const _size = 2
)
Set the value of a configurable parameter in a device. Some devices have various parameters that can be configured to control the device behavior. These are not reported by the device over the Z-Wave network, but can usually be found in the device's user manual. This method returns immediately, without waiting for confirmation from the device that the change has been made.
Parameters
_homeId The Home ID of the Z-Wave controller that manages the node.
_nodeId The ID of the node to configure.
_param The index of the parameter.
_value The value to which the parameter should be set.
_size Is an optional number of bytes to be sent for the parameter _value. Defaults to 2.
Returns
true if the a message setting the value was sent to the device.
*/
// called for each node ready
function fillDevices(node, productIDTotal, nodes, zwave) {
switch (productIDTotal) {
case "0086-0003-0062": // Aeotec, ZW098 LED Bulb
case "0086-0103-0062": // Aeotec, ZW098 LED Bulb
case "0086-0203-0062": // Aeotec, ZW098 LED Bulb
case "0131-0002-0002": // Zipato, RGBW LED Bulb
(node.senderID !== undefined)? node.typeNode = "zwave-light-dimmer-switch" : node.type = "zwave-light-dimmer-switch";
node.commandclass = "38";
node.classindex = "0";
break;
case "0165-0002-0002": // NodOn, CRC-3-6-0x Soft Remote
(node.senderID !== undefined)? node.typeNode = "nodonSoftRemote" : node.type = "nodonSoftRemote";
zwave.setConfigParam(node.senderID, 3, 1, 1); // Enable scene mode for the SoftRemote
break;
case "010f-0600-1000": // FIBARO System, FGWPE Wall Plug
case "010f-0f01-1000": // FIBARO Button
case "0165-0001-0001": // NodOn, ASP-3-1-00 Smart Plug
case "0060-0004-0001": // AN157 Plug-in switch
case "0060-0003-0003": // Everspring AD147 Plug-in Dimmer Module
(node.senderID !== undefined)? node.typeNode = "zwave-binary-switch" : node.type = "zwave-binary-switch";
node.commandclass = "37";
node.classindex = "0";
break;
case "010f-0800-1001": // FIBARO System, FGMS001 Motion Sensor
case "010f-0800-2001": // FIBARO System, FGMS001 Motion Sensor
case "010f-0800-4001": // FIBARO System, FGMS001 Motion Sensor
case "010f-0801-1001": // FIBARO System, FGMS001 Motion Sensor
case "010f-0801-2001": // FIBARO System, FGMS001 Motion Sensor
(node.senderID !== undefined)? node.typeNode = "zwave-generic" : node.type = "zwave-generic";
// (node.senderID !== undefined)? node.typeNode = "zwave-motion-sensor" : node.type = "zwave-motion-sensor";
node.commandclass = "48";
node.classindex = "0";
break;
case "010f-0700-1000": // FIBARO System, FGK101 Door Opening Sensor
case "010f-0700-2000": // FIBARO System, FGK101 Door Opening Sensor
case "010f-0700-3000": // FIBARO System, FGK101 Door Opening Sensor
case "010f-0700-4000": // FIBARO System, FGK101 Door Opening Sensor
(node.senderID !== undefined)? node.typeNode = "zwave-generic" : node.type = "zwave-generic";
//(node.senderID !== undefined)? node.typeNode = "zwave-binary-sensor" : node.type = "zwave-binary-sensor";
node.commandclass = "48";
node.classindex = "0";
break;
case "0086-0002-004a": // Aeotec, ZW074 MultiSensor Gen5
case "0086-0102-004a": // Aeotec, ZW074 MultiSensor Gen5
case "0086-0202-004a": // Aeotec, ZW074 MultiSensor Gen5
case "0086-0002-0064": // Aeotec, ZW074 MultiSensor 6
case "0086-0102-0064": // Aeotec, ZW074 MultiSensor 6
case "0086-0202-0064": // Aeotec, ZW074 MultiSensor 6
(node.senderID !== undefined)? node.typeNode = "zwave-generic" : node.type = "zwave-generic";
// (node.senderID !== undefined)? node.typeNode = "aeotecMultiSensor" : node.type = "aeotecMultiSensor";
node.commandclass = "48";
node.classindex = "0";
// Config
// https://aeotec.freshdesk.com/helpdesk/attachments/6053297241
zwave.setConfigParam(node.senderID, 2, 1, 1); // Enable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.
zwave.setConfigParam(node.senderID, 3, 30, 2); // Set the time(sec) that the PIR stay ON before sending OFF
/*
1. The default PIR time is 4 minutes. The Multisensor will send BASIC SET
CC (0x00) to the associated nodes if no motion is triggered again in 4
minutes.
2. Range: 10~3600.
Note:
1. The time unit is second if the value range is in 10 to 255.
2. If the value range is in 256 to 3600, the time unit will be minute and its
value should follow the below rules:
a. Interval time =Value/60, if the interval time can be divided by 60
and without remainder.
b. Interval time= (Value/60) +1, if the interval time can be divided by
60 and has the remainder.
3. Other values will be ignored.
*/
zwave.setConfigParam(node.senderID, 4, 2, 1); // PIR sensitivity
/*
Set the sensitivity of motion sensor.
0 = the current PIR sensitivity level=0. (minimum level)
1 = the current PIR sensitivity level=1.
2 = the current PIR sensitivity level=2.
3 = the current PIR sensitivity level=3.
4 = the current PIR sensitivity level=4.
5 = the current PIR sensitivity level=5. (maximum level)
*/
zwave.setConfigParam(node.senderID, 5, 1, 1); // send PIR detection on binary sensor command class
zwave.setConfigParam(node.senderID, 81, 0, 1); // no LED blinking when PIR detection
zwave.setConfigParam(node.senderID, 111, 900, 4); // interval time (s) of sending reports (900 = 15mn)
console.log("zwave.setConfigParam Aeotec, MultiSensor");
break;
default:
console.log("Node " + node.senderID + " handled as generic. (productID:" +productIDTotal + ")");
(node.senderID !== undefined)? node.typeNode = "zwave-generic" : node.type = "zwave-generic";
node.commandclass = Object.keys(nodes[node.senderID].classes)[0]; // https://developer.mozilla.org/fr/docs/Web/JavaScript/Reference/Objets_globaux/Object/keys
node.classindex = Object.keys(nodes[node.senderID].classes[node.commandclass])[0];
break;
}
}
module.exports = {
'fillDevices': fillDevices
};