node-rpi-rgb-led-matrix-adafruit
Version:
control led matrix with nodejs on raspberry pi. Nodejs binding of https://github.com/hzeller/rpi-rgb-led-matrix
102 lines (83 loc) • 4.15 kB
Plain Text
# Creating RGB matrix library
# When you link this library with your binary, you need to add -lrt -lm -lpthread
# So
# -lrgbmatrix
##
OBJECTS=gpio.o led-matrix.o framebuffer.o thread.o bdf-font.o graphics.o transformer.o
TARGET=librgbmatrix.a
###
# After you change any of the following DEFINES, make sure to 'make clean'
# and make again
###
# If you see that your display is inverse, you might have a matrix variant
# has uses inverse logic for the RGB bits. In that case: uncomment this.
#DEFINES+=-DINVERSE_RGB_DISPLAY_COLORS
# Some panels out there seem to have Green and Blue swapped (even though the
# writing on connector looks correct). This option will swap these colors if
# you happen to have gotten such panel.
#DEFINES+=-DRGB_SWAP_GREEN_BLUE
# For curiosity reasons: uncomment to see refresh rate in terminal.
#DEFINES+=-DSHOW_REFRESH_RATE
# The signal can be too fast for some LED panels, in particular with newer
# (faster) Raspberry Pi 2s.
# In these cases, you want to make sure that
# - The cables are short enough from the GPIO header to the panel.
# - Maybe use an active level shifter and bus driver, for instance by building
# up one of the adapter-PCBs in the ../adapter/ directory or use
# the Adafruit HAT. The output drivers of the GPIO are not really good
# in driving long cables - this will improve the situation.
#
# If the above fails or you can't implement them, try uncommenting the
# following line and recompile; it will slow down GPIO, but will as well reduce
# the frame-rate.
# Sometimes, you even have to give RGB_SLOWDOWN_GPIO=2 for particularly slow
# panels or bad signal cable situations.
DEFINES+=-DRGB_SLOWDOWN_GPIO=1
# ------------ Pinout options; usually no change needed here --------------
# Uncomment the following line for Adafruit Matrix HAT gpio mappings.
# If you have an Adafruit HAT ( https://www.adafruit.com/products/2345 ),
# you need to use this option as the HAT swaps pins around that are not
# compatible with the default mapping.
#DEFINES+=-DADAFRUIT_RGBMATRIX_HAT
# Uncomment if you want to use the Adafruit HAT with stable PWM timings.
# The newer version of this library allows for much more stable (less flicker)
# output, but it does not work with the Adafruit HAT unless you do a
# simple hardware hack on them:
# connect GPIO 4 (old OE) with 18 (the new OE); there are
# convenient solder holes labeled 4 and 18 on the Adafruit HAT, pretty
# close together.
# Then uncomment the following define and recompile.
#DEFINES+=-DADAFRUIT_RGBMATRIX_HAT_PWM
# Compatibility option, usually not needed.
# If you have used this library before July 2015 and have wired it up for that,
# then you need to define RGB_CLASSIC_PINOUT for your panel to work. The
# standard pinout changed so that we can make use of the PWM pin for much
# more stable timing. So even if you have the classic pinout, you might
# consider wiring up the new one (sorry for the inconvenience).
#DEFINES+=-DRGB_CLASSIC_PINOUT
# If you use RGB_CLASSIC_PINOUT and use Raspberry Pi 1, Revision A,
# this might be useful.
#DEFINES+=-DONLY_SINGLE_CHAIN
# Typically, a Hub75 panel is split in two half displays, so that a 1:16
# multiplexing actually multiplexes over two half displays and gives 32 lines.
# There are some other displays out there that you might experiment with
# that are internally wired to only have one sub-panel. In that case you might
# want to try this define to get a more reasonable canvas mapping.
# This option is typically _not_ needed, only use when you attempt to connect
# some oddball old (typically one-colored) display, such as Hub12.
#DEFINES+=-DONLY_SINGLE_SUB_PANEL
INCDIR=../include
CXXFLAGS=-Wall -O3 -g -fPIC $(DEFINES)
$(TARGET) : $(OBJECTS)
ar rcs $@ $^
led-matrix.o: led-matrix.cc $(INCDIR)/led-matrix.h
thread.o : thread.cc $(INCDIR)/thread.h
framebuffer.o: framebuffer.cc framebuffer-internal.h
graphics.o: graphics.cc utf8-internal.h
%.o : %.cc compiler-flags
$(CXX) -I$(INCDIR) $(CXXFLAGS) -c -o $@ $<
clean:
rm -f $(OBJECTS) $(TARGET)
compiler-flags: FORCE
@echo '$(CXXFLAGS)' | cmp -s - $@ || echo '$(CXXFLAGS)' > $@