iobroker.espresense/admin/i18n/zh-cn/translations.json

Connect to ESPresense

{
    "espresense adapter settings": "espresense的适配器设置",
    "option1": "选项1",
    "option2": "选项2",
    "MQTTUseServer": "启动自己的mqtt服务器",
    "MQTTUseServerHint": "在 ESPresence 中输入此处输入的用户名、密码和端口。输入 iobroker 的 Ip 作为 mqtt-server。 iobroker 上的端口必须空闲。",
    "MQTTServerIp": "外部mqtt服务器的服务器ip",
    "MQTTServerPort": "端口 (1024-49151)",
    "MQTTUsername": "用户名",
    "MQTTPassword": "密码",
    "unseenTime": "设备显示为缺席后的时间。",
    "genericStateObjects.presense": "存在感",
    "genericStateObjects.customString": "用户数据点",
    "devices.folder": "设备文件夹",
    "rooms.folder": "房间文件夹(ESP32)",
    "settings.folder": "设置文件夹（ESPreense 配置）",
    "genericStateObjects.state": "无定义（向开发人员报告）",
    "room.known_irks": "已知的烦恼",
    "room.known_macs": "已知的Mac",
    "room.query": "询问",
    "room.exclude": "排除的 ID",
    "room.status": "ESPresense 状态",
    "room.distance": "最大距离",
    "room.absorption": "吸收",
    "room.tx_ref_rssi": "TX 参考 RSSI",
    "room.rx_adj_rssi": "RX调整RSSI",
    "room.include": "包含 ID",
    "room.count_ids": "统计ID数",
    "room.arduino_ota": "Arduino OTA 更新",
    "room.auto_update": "自动更新",
    "room.prerelease": "在自动更新中包含预发布版本",
    "room.motion": "运动传感器",
    "room.switch": "转变",
    "room.button": "按钮",
    "room.pri_timeout": "PIR 运动超时（以秒为单位）",
    "room.radar_timeout": "雷达运动超时（以秒为单位）",
    "room.switch_1_timeout": "交换机一超时（以秒为单位）",
    "room.switch_2_timeout": "切换两次超时（以秒为单位）",
    "room.button_1_timeout": "按钮一超时（以秒为单位）",
    "room.button_2_timeout": "按钮二超时（以秒为单位）",
    "room.led_1.channel": "发光二极管1",
    "room.led_1.state": "转变",
    "room.led_1.brightness": "亮度",
    "room.led_1.color.channel": "LED颜色",
    "red": "红色的",
    "blue": "蓝色的",
    "green": "绿色的",
    "room.telemetry.channel": "遥测",
    "room.telemetry.ip": "网络地址",
    "room.telemetry.uptime": "正常运行时间",
    "room.telemetry.firm": "模型",
    "room.telemetry.rssi": "接收信号强度",
    "room.telemetry.ver": "版本",
    "room.telemetry.count": "数数",
    "room.telemetry.adverts": "广告",
    "room.telemetry.seen": "见过",
    "room.telemetry.reported": "已报道",
    "room.telemetry.freeheap": "自由堆",
    "room.telemetry.maxHeap": "最大堆",
    "room.telemetry.scanStack": "扫描堆栈",
    "room.telemetry.loopStack": "循环栈",
    "room.telemetry.bleStack": "BLE 堆栈",
    "devices.mac": "MAC地址",
    "devices.id'": "设备 ID（用于包含/排除）",
    "devices.name": "友好名称",
    "devices.disc": "光盘",
    "devices.idType": "id类型",
    "devices.rssi@1m": "RSSI@1m",
    "devices.rssi": "tssi",
    "devices.raw": "生的",
    "devices.distance": "距离",
    "devices.int": "整数",
    "devices.close": "关闭",
    "settings.config.channel": "配置",
    "settings.config.id": "Device ID",
    "settings.config.name": "友好名称",
    "deviceHeader": "设备",
    "selectDevice": "用于添加/删除的设备选择",
    "addDevice": "添加设备",
    "removeDevice": "删除设备",
    "selectedDevices": "所有已知设备",
    "room.button_1": "按钮1",
    "room.restart": "重新开始",
    "genericStateObjects.deviceDB": "管理员设备概览",
    "retainGlobalTip": "您可以使用 global 同时更新所有 ESPresense 基站。如果激活此选项，即使新节点也会在启动时获取配置。注意只有更改的状态才会被保存为保留。",
    "retainGlobal": "保留",
    "settings.global": "全局设置",
    "name": "姓名",
    "devices.convert": "换算系数",
    "devices.convert.desc": "在此输入到 ESP 的实际距离（以米为单位），适配器将计算该系数。",
    "devices.distanceConverted": "换算距离",
    "MQTTHandleInterval": "收集传入 Mqtt 消息的周期 - 减少系统负载。 （以秒为单位，分钟 3）",
    "devices.devices.friendlyName": "友好的房间名称",
    "convertFactor": "转换因子",
    "room.distanceIoBroker": "计算在适配器内部"
}