homebridge-unifi-protect/dist/settings.js

Homebridge UniFi Protect plugin providing complete HomeKit integration for the entire UniFi Protect ecosystem with full support for most features including HomeKit Secure Video, multiple controllers, blazing fast performance, and much more.

/* Copyright(C) 2022-2025, HJD (https://github.com/hjdhjd). All rights reserved.
 *
 * settings.ts: Settings and constants for homebridge-unifi-protect.
 */
// The name of our plugin.
export const PLUGIN_NAME = "homebridge-unifi-protect";
// The platform the plugin creates.
export const PLATFORM_NAME = "UniFi Protect";
// How often, in seconds, should we check Protect controllers for new or removed devices.
export const PROTECT_CONTROLLER_REFRESH_INTERVAL = 120;
// How often, in seconds, should we retry getting our bootstrap configuration from the Protect controller.
export const PROTECT_CONTROLLER_RETRY_INTERVAL = 10;
// Default delay, in seconds, before removing Protect devices that no longer exist.
export const PROTECT_DEVICE_REMOVAL_DELAY_INTERVAL = 60;
// Default duration, in milliseconds, of the authentication contact sensor for a Protect doorbell, primarily for automation purposes.
export const PROTECT_DOORBELL_AUTHSENSOR_DURATION = 5000;
// Default duration, in milliseconds, of a physical digital chime attached to a Protect doorbell. This value comes from UniFi Protect itself.
export const PROTECT_DOORBELL_CHIME_DURATION_DIGITAL = 1000;
// Default duration, in milliseconds, to wait before allowing another trigger of the buzzer or speaker on the chime.
export const PROTECT_DOORBELL_CHIME_SPEAKER_DURATION = 3500;
// Default duration, in milliseconds, of the trigger switch for a Protect doorbell, primarily for automation purposes.
export const PROTECT_DOORBELL_TRIGGER_DURATION = 5000;
// FFmpeg afftdn audio filter defaults - this setting uses FFTs to reduce noise in an audio signal by the number of decibels below.
export const PROTECT_FFMPEG_AUDIO_FILTER_FFTNR = 90;
// FFmpeg highpass audio filter defaults - this setting attenuates (eliminates) frequencies below the value.
export const PROTECT_FFMPEG_AUDIO_FILTER_HIGHPASS = 200;
// FFmpeg lowpass audio filter defaults - this setting attenuates (eliminates) frequencies above the value.
export const PROTECT_FFMPEG_AUDIO_FILTER_LOWPASS = 1000;
// Protect's native I-frame interval can vary, but the livestream API seems to default to 5 seconds at most, though it depends on camera type and stream quality selected.
export const PROTECT_LIVESTREAM_API_IDR_INTERVAL = 5;
// HomeKit Secure Video segment resolution, in milliseconds. This defines the resolution of our buffer. It should never be less than 100ms or greater than 1500ms.
export const PROTECT_HKSV_SEGMENT_RESOLUTION = 100;
// HomeKit Secure Video communication timeout threshold, in milliseconds. HKSV has a strict 5 second threshold for communication, so we set this a little below that.
export const PROTECT_HKSV_TIMEOUT = 4500;
// HomeKit Secure Video timeshift buffer default duration, in milliseconds. This defines how far back in time we can look when we see a motion event.
export const PROTECT_HKSV_TIMESHIFT_BUFFER_MAXDURATION = PROTECT_LIVESTREAM_API_IDR_INTERVAL * 1000 * 2;
// Default port to use to publish an M3U playlist for use in other apps that can consume one to make camera livestreams available, such as Channels DVR.
export const PROTECT_M3U_PLAYLIST_PORT = 10110;
// Default duration, in seconds, of motion events. Setting this too low will potentially cause a lot of notification spam.
export const PROTECT_MOTION_DURATION = 10;
// Default MQTT topic to use when publishing events. This is in the form of: unifi/protect/camera/event
export const PROTECT_MQTT_TOPIC = "unifi/protect";
// Default duration, in seconds, of occupancy events.
export const PROTECT_OCCUPANCY_DURATION = 300;
// Minimum required GPU memory on a Raspberry Pi for hardware acceleration.
export const PROTECT_RPI_GPU_MINIMUM = 128;
// Maximum age of a snapshot in seconds.
export const PROTECT_SNAPSHOT_CACHE_MAXAGE = 90;
// Bitrate, in kilobits per second, to use when transcoding to local clients.
export const PROTECT_TRANSCODE_BITRATE = 2000;
// Bitrate, in kilobits per second, to use when transcoding to high-latency clients.
export const PROTECT_TRANSCODE_HIGH_LATENCY_BITRATE = 1000;
//# sourceMappingURL=settings.js.map